# How to recover a dining chair seat pad and back

A plain guide to recovering a dining chair seat pad and back: taking off old covers, cutting fabric, adding foam and stapling a neat new finish.

Recovering a dining chair seat pad and back means removing the old cover, checking the padding, and stapling new upholstery fabric over the seat base and the back panel. You can cover a seat pad on its own, or take on the seat and back together for a matching set. The job needs a staple gun, fabric, foam where the padding has flattened, and a little patience with corners. 

- Take the seat pad off the chair frame before you cut any fabric.
- Keep the old cover as a template so the new one fits the pad.
- Replace foam that has gone flat, then add a thin layer of wadding.
- Pull fabric evenly and staple opposite sides in turn to avoid wrinkles.
- Finish the back panel so no raw edges or staples show.
 

## Look at what the chair is made of 

The first step in recovering a dining chair is to look at how the seat and back are built. Many dining chairs have a seat pad screwed to the frame from below, which comes off with a screwdriver. Some have the fabric stapled straight onto a fixed frame, and those need a different approach. 

Check the back of the chair as well, because chair back reupholstery often means a separate panel. A back panel may be stapled on, held by a wooden trim, or slipped into a groove. Understanding the fixings before you buy fabric keeps the job simple. 

Note the shape of the seat pad and any curves in the frame. Curved edges and rounded corners need more fabric and more careful pleating. If the frame is glued or badly cracked, a furniture repairer should look at it before you add new upholstery. 

## Remove the old seat pad and cover 

Seat pad removal starts with turning the chair upside down and taking out the screws that hold the pad. Keep the screws in a small container so they do not go missing. Once the pad is free, prise out the old upholstery staples with a staple remover or a flat screwdriver. 

Work around the edge slowly and lift the old fabric away without tearing it. The old cover is useful as a pattern for the new one, so keep it flat. Pull out any staples left in the wood, because they catch fabric and hands. 

If the chair has a back panel, remove it in the same careful way. Label the panels if you are covering more than one chair, so each cover goes back on the right frame. Take a photo of the layers before you strip them, in case you need to rebuild the order. 

## Check and replace the foam padding 

Foam padding flattens with use, and new fabric sits better on fresh foam. Press the old foam with your hand; if it stays compressed or crumbles at the edges, replace it. Choose foam of a similar thickness so the seat still fits the frame. 

Cut the new foam to the shape of the seat base with a sharp knife and a steady cut. A thin layer of wadding over the foam softens the edges and hides the line of the frame. Spray adhesive holds the wadding in place while you pull the fabric. 

For the back, use thinner foam than the seat, or none at all if the back panel is flat. A dining chair seat cushion that is too thick changes the height of the chair and the angle of your back. Keep the padding modest and even across the panel. 

## Measure and cut the new fabric 

Fabric measuring for a chair seat pad needs more than the pad size, because the fabric wraps around the edges. Add enough allowance on every side to reach the underside of the pad and overlap the staples. A generous allowance can be trimmed later, but a short piece cannot be stretched. 

Lay the old cover on the new upholstery fabric and trace around it, then add the allowance. Match any pattern repeat across the seat and back if the fabric has a design. Cut with sharp scissors and check the piece against the pad before you staple. 

For a set of chairs, cut all the pieces at once so the pattern lines up and the color matches. Fabric with a little stretch is easier to pull around curves. A woven upholstery fabric holds its shape well on a seat that gets daily use. 

## Staple the seat cover in place 

A staple gun makes fast work of fixing the new cover to the seat base. Center the fabric on the pad and staple one edge at the middle, then pull the opposite edge and staple it. Working in opposite pairs keeps the fabric even and stops wrinkles forming. 

At corners, fold the fabric into neat pleats and staple each fold flat. Pull firmly but not so hard that the pattern distorts. Upholstery staples should sit flush with the wood and not tear through the fabric. 

Trim the excess fabric after stapling, leaving a small margin beyond the staples. Fold the raw edge under before the final staples so it does not fray. Turn the pad over and check that the surface is smooth before you screw it back on. 

## Cover the chair back panel 

Chair back reupholstery follows the same pull and staple method as the seat, but the panel is smaller and often curved. Center the pattern on the back and staple the top edge first. Pull the fabric down and staple the bottom edge, then work along the sides. 

Many chair backs have a front face and a rear face, and the rear one hides the staples. Cover the front, then add a chair back cover or a plain panel on the rear side. Staple the rear panel over the folded edges so the finish looks clean from behind. 

If the back panel slides into a groove, press the fabric into the groove with a blunt tool before you fix the trim. Trim pieces and piping hide the join between the seat and the back. Check that the back sits straight on the frame before the final screws go in. 

## Choose fabric for seats and backs 

Upholstery fabric for a dining chair needs to take rubbing and hold a staple without fraying. Tight weaves such as canvas, linen blends and woven synthetic mixes work well on a seat pad. Very loose weaves pull apart at the staple line. 

Color choice affects how the chair sits in the room, so hold a fabric sample against the table and the floor in daylight. A mid-tone fabric shows fewer marks than a very pale one, and a pattern hides small stains better than a plain surface. Think about the whole set rather than one chair. 

Fabric weight matters on the back panel, where a heavy cloth can sag. A medium-weight cloth pulls neatly around curves and corners. If you plan to change seat covers again later, a removable cover with a zip is easier to wash than a stapled one. 

## Finish the job and care for the cover 

Seat cover replacement ends with the pad screwed back on and the chair standing level. Check every screw and tighten any that are loose. Run a hand over the seat and back to feel for staples that sit proud or fabric that has pulled tight. 

Vacuum the new cover with a soft brush to lift dust from the weave. Blot spills straight away with a clean cloth rather than rubbing them into the fabric. A fabric protector can be applied before the chair goes back into use. 

Inspect the staples and seams now and then, especially on chairs that get heavy use. A loose staple can be tapped back or replaced before the fabric tears. If the frame loosens or the foam collapses again, the cover can be taken off and the padding renewed. 

## Questions about recovering dining chairs 

### Can I cover a dining chair seat without removing the pad? 

Yes, you can cover a dining chair seat pad while it stays on the frame, but the finish is harder to get neat. Fabric must be tucked and stapled under the seat, which is awkward in a closed frame. Removing the pad gives a smoother result and lets you check the foam. 

### How do I recover a dining chair seat and back together? 

Recovering a dining chair seat and back together means treating them as two separate panels with the same fabric. Cover the seat pad first, then the back panel, matching the pattern across both. Keep the old covers as templates so each piece fits its own panel. 

### What fabric should I use for a dining chair seat pad? 

A tightly woven upholstery fabric is the sensible choice for a dining chair seat pad. It holds a staple, resists fraying and takes daily rubbing better than a loose dress fabric. Check that the cloth can be pulled around corners without the weave opening. 

### Do I need to replace the foam when I reupholster a chair? 

You only need to replace foam padding that has flattened, crumbled or lost its shape. Foam in good condition can stay under the new cover with a thin layer of wadding on top. New foam of a similar thickness keeps the seat height and comfort the same. 

### How do I change seat covers on dining chairs with a fixed frame? 

Changing seat covers on a dining chair with a fixed frame means stapling the new fabric directly onto the frame. Work from the middle of each edge outward and fold the corners into pleats. Trim the excess fabric and cover the staple line with trim if it shows. 

### What tools do I need to recover a dining chair? 

A staple gun, upholstery staples, a staple remover, scissors and a screwdriver cover most of the job. Add foam and wadding if the padding needs renewing, and a blunt tool for pressing fabric into grooves. A cutting mat and a sharp knife help with trimming foam.
